1/29/2024 0 Comments Loxone relay extension![]() The device must not be used as part of safety-critical systems. The installation requires a suitable enclosure to ensure protection against contact, water and dust. The installation must be carried out by a qualified technician in accordance with all applicable regulations. When selected, you will be notified via System Status or the Mailer if the device is no longer available or goes offline. Save into the Miniserver, in order to pair the Extension.Īfterwards the program must be loaded from the Miniserver to transfer the actual serial number of the Extension into the program. This can only be used if there is only one Extension of the same type. Specifies the serial number of the device.įor Extensions: Enter 'Auto' to automatically pair an extension with unknown serial number. 9 TE (dimensions: 155 x 85 x 49mm) Power supply 24VDC. With its fourteen 16A rated relays, it will switch even the heaviest loads with ease. Switch currents of over 5A (up to 16A) with the Miniserver or Extension's digital output. Use 230V sensors (such as 230V motion detectors) with the 24V inputs on the Miniserver or Extension. This can be due to short-circuits, overloaded switching loads or too high an ambient temperature. The Relay Extension is a true powerhouse. Item no.: 200049 This high quality 16A coupling relay is ideal in conjunction with a Loxone control system. If the CPU temperature reaches a critical point, the outputs of the device are switched off. The Extension starts after switching on the power supply, and the status LED will flash orange after a short time when the connection to the Miniserver is established. For loads exceeding 12A, use a wire cross-section of 2.5mm².įor thermal reasons the total load rating must not exceed 48A (IEC) or 45A (UL). The Relay Extension is installed on a DIN rail in a suitable enclosure.Ĭonnect the power supply and Link communication to the Miniserver.Ĭonnect the loads to the relay terminals. ![]() 10 pcs of sensors Dallas DS18B20, DS2438 (Unica 1wire sensor.The Relay Extension features 14 dry contact relay outputs.ĭatasheet Relay Extension Table of Contents 2xanalog outputs - output voltage 0 - 10V 2x analog inputs - input voltage 0 - 10V, resolution 1024 bitů 4x digital outputs Low side switch - load current max 2A for 1 output, max 24V DC 4xdigital outputs High side switch - load current max 2A for 1 output, max 24V DC input current 7A/5A at 230V AC for 1 output Der Bus wird mit zwei Adern (Link+ und Link-) von Gert zu Gert gefhrt. es ist nicht mglich, andere CAN-Bus Gerte an den Loxone Link anzuschlieen. Das Busprotokoll ist dennoch proprietr, d.h. 12xrelay outputs - galvanically separated, max. Der Loxone Link (frher als 'LoxBUS' bezeichnet) basiert technisch auf dem CAN-Bus. 24x digital inputs - optically separated, max. Version 2.1 - better protection of internal power supply, removed bug for L4 output, improved EMC compatibility There can be connected up to 15 Railduino modules within the same network/bus. Both types of connections communicate using UDP protocol (User defined protocol). Inputs/outputs can be read/controlled by communication bus RS485 or by LAN within computer network. Module can handle 1-wire devices (Maxim/Dallas) as favourite temperature sensors DS18B20 or DS2438 ( Unica 1wire sens. There are also relay, digital and analog outputs - see the table below. You will need programming and installation by a certified Loxone Partner. Module is equipped with both digital and analog inputs. lights, pumps etc.) using outputs or sense the values at the inputs of the module (e.g. With this connection the control system is able to control external devices (e.g. The Loxone Relay Extension is a device for automatic control. to control blinds, lights, heating and more 14 digital outputs (relays) max. 250VAC 16A at cos 1 (IEC) total load whole Extension max. Loxone) as so called distributed inputs / outputs. The Loxone Relay Extension is a true powerhouse and with its fourteen 16A rated relays, it will switch even the heaviest loads with ease. Railduino module is a device working in connection with superior control system (e.g.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |